How to Do a Door Lock Change

Changing your door lock is an easy and inexpensive way to increase the security of your home. However, this procedure is not for everyone. It requires a certain amount patience and expertise.

The cylinder is located within the knob's body. The cylinder is what recognizes the key when it is put into the lock.

Removing the old lock

The first step to replace a door lock is to remove the old lock. This is a relatively easy process, however there are a few things to be aware of. First, ensure that the lock you choose to install is the right size for the door you have. This will ensure it is secure and doesn't leave a gap at the latch or deadbolt.

After removing the latch plate, you will need to look for two screws or bolts on the inside of the casing which are holding the casing in place with the lock halves. Remove these screws with a screwdriver before removing the lock off the door. If you are using a mortise locking system there is an anchor screw that connects the handle to the spindle. Take off the doorknobs by removing this screw using the help of a screwdriver.

Remove the deadbolt and latch plug from the door jamb. Install your new lock. If you're replacing a mortise you should measure the distance between the lock case and the door edge to ensure that the new lock is a good fit.

Several reasons might prompt you to replace your door lock, such as being concerned that someone else may have the key or if you're welcoming the arrival of a new roommate. You could save money if you take the lock off yourself instead of hiring an expert. The process is simpler than most people think, and it can be completed in a few minutes.

Start by taking the trim and handle from the door. With a flat screwdriver pry off the trim. You should be able to twist off the majority of it. In some instances you may be able to remove the handles completely. Then, check the handle for a small pinhole on the inside and insert a straightened paper clip into it. This will trigger the release mechanism and allow you to take the handle from the door. The next step is to look at the interior side of the lock for another small tab and press it with a flat screwdriver. After the spindle is removed, you can remove the housing and cylinder.

Selecting a new lock

There are many options to choose from when it comes time to pick the right lock. Take a look at the various types of double glazing locks glazed doors locks; http://m.yuulyie.com/, and select one that matches the style of your door. Consider the backset which is the distance between the edge and the middle of the hole in the lock. Also, think about the cross bore, which is a small hole in the middle of your door frame. Also, ensure that you choose a lock that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded the majority of door locks to give you an idea of their strength and how difficult it is to pick them or disable them. A lock grade 3 might be the ideal choice for a tranquil apartment in the country, while locks of grade 1 may be better suited to a busy street near a storefront.

Most smart door locks require digital code to open. If you are concerned about hacking or other security concerns, consult a professional locksmith.

Replacing the cylinder

If the cylinder of your door lock is broken or damaged it can be replaced within a matter of minutes with a simple do-it-yourself project. The trick is to select the right cylinder and follow the steps that are included with it. First, you must remove the handle or knob if it is present. Then using a screwdriver unscrew the trim that surrounds the lock cylinder. After the trim has been removed, it is possible to remove the screws that hold the cylinder with the flathead. The cylinder is then gently removed out of the door.

Be sure to take measurements of the length of the new cylinder prior to installing it. With a tape measure, measure the distance between the cylinder's center and its right and left sides. Purchase a new cylinder which has the same measurements. This will stop cylinders from snapping when the door is kicked or [Redirect-Java] the key gets stuck inside.

Place the replacement upvc door locks cylinder inside the door, and then turn the key. This will align the cylinder with the carrier that is usually located on the outside of your lock. Then, you can loosen the set screw which should be just a few turns inside the head. You will also need to loosen the screw at the door's edge that fastens the case, if there is one.

You can replace the old lock cylinder with a new one by slipping it into the case, and then tightening the set screws. It is also recommended to reinstall the part that connects the cylinder to the stem of the lock indicator that you can do by removing three small tabs on back of the cylinder with needle-nose pliers. Attach the smaller bracket to the cylinder's back. Then, you need to install the strike plate and latch plate, as well as the retaining ring that is attached to the top of the lock cylinder.

Installing a new lock

Begin by measuring the door's width if are replacing an existing lock. Most residential locksets have a thickness of 1 3/8 inch to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll require a stronger door kit. This will include longer screws, or an extension for the spindle or a longer tail piece for door knobs.

The majority of locks come with a detailed instruction booklet to assist you in installing the new hardware. Before you begin, read the instructions to make sure you've followed all the steps. The manual will give you a good idea of the level of skill that is required to complete the task. You might want to ask a person who has had experience in changing replacement window locks for assistance if are changing locks for the first time.

It's a good idea to cover the holes in the old lock before installing the new lock. This will prevent the screws from falling out of the holes and will protect any tile you might have put in the area. It will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a piece of painter's tape that is intended to be used for this purpose, but you can also use gaffer's tape as well as masking tape when you have it.

Once you've removed the screws that connect the inside of the lock section to the outside side immediately, pull it back. It's crucial to do this quickly so that the lock doesn't end up accidentally closing itself and damaging the mechanism.

Fit the new latch bolt in the upper cross bore of your new lock if it has one. Make sure you place it in the correct place, which is usually marked by an indication on the faceplate. Then, screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plate into the door jamb. Test the deadbolt by throwing it a few times to verify that it extends all the way through the strike plate and is secured. If you're using an electronic smart lock, be certain to follow the instructions for programming it. This involves downloading an app, creating an email address, verifying your identity, and accessing the wireless network to add your device.